|
Unit |
Electra Elite IPK KSU/CPU/Port Expansion Kit/KSU Expansion |
Stock Number |
|
Elite IPK II Basic PKG (V1000) |
ELECTRA ELITE IPK II BASIC PKG The Package contains the following
items; - B64-U30 KSU (750015) - CPUII (100)-U10 ETU (750048) - ESIB
(8)-U20 ETU (750211) |
750018 |
|
B64-U30 KSU |
KEY SERVICE UNIT The Key Service Unit (KSU) for the Electra Elite IPK
II system can be expanded to a maximum of 456 ports with the addition
of 2 expansion KSUs depending on the configuration: (Same unit is used
as expansion KSU) The P64-U(20) PSU (power supply unit) and backup
batteries are included. |
750015 |
|
CPUII (100)-U10 ETU |
CENTRAL PROCESSING UNIT The Central Processing Unit ETU contains a
32-bit microprocessor that controls the system. Included are Ethernet
port, 64 conference ports, 64-channel PBR circuits, a tone generator,
and MOH input. Provides synchronization for T1 lines, ISDN basic and
prime rate interface (CLKG built-in). One required per basic IPK KSU.
Compact Flash Memory Card is required for Remote software download. |
750048 |
|
EXP-U10 ETU |
EXPANSION CABINET INTERFACE The Expansion ETU is installed in the
B64-U20 KSU for expansion. One EXP-U10 is required per expansion KSU. |
750140 |
|
PKUII-U Unit |
ELECTRA ELITE IPK PORT KEY UPGRADE This Port Upgrade chip is installed
on the CPUII (100)-U10. This expands the system capacity from 64 ports
to 456 Ports. |
750110 |
|
MOD-U10 Modem Kit |
33.6Kbps MODEM UNIT for CPUII This unit piggybacks on CPUII ( )-U10.
Note: Only required for Modem Connection. Ethernet Built on CPU II |
750464 |
|
CPUII CF BLANK |
128MB Compact Flash disk for CPUII slot This flash disk is required
for remote software upgrade. To activate remote software upgrade, the
remote s/w activation key (750879) is also required. |
750889 |
|
Elite IPK to IPK II Firmware Upgrade CD |
CD-ROM with Firmware Upgrade. May also be upgraded by download from
the Website, excluding CCH. Upgrade chip for CCH included with this
Package. |
750881 |
|
Unit |
IPK II Quick Start Packages |
Stock Number |
|
Package 1 4x8 |
Component
QTY |
750075 |
|
IPK II Basic PKG 750018 1 |
|
DSPII-U10 UNIT 750118 1 |
|
COIB(4)-U30 ETU 750449 1 |
|
InMail 2Port / 8Hours 750558 1 |
|
DTH-8D-2 (BK) TEL 780571 7 |
|
DTH-16D-2 (BK) TEL 780575 1 |
|
|
|
|
Package 2 8x8 |
Component
QTY |
750076 |
|
IPK II Basic PKG 750018 1 |
|
DSPII-U10 UNIT 750118 1 |
|
COIB(8)-U30 ETU 750451 1 |
|
InMail 4Port / 8Hours 750559 1 |
|
DTH-16D-2 (BK) TEL 780575 8 |
|
|
|
|
Package 3 PRIx12 |
Component
QTY |
750077 |
|
IPK II Basic PKG 750018 1 |
|
VMP(x)-U40 ETU 750528 1 |
|
DTI-U40 ETU 750196 1 |
|
ESIE(8)-U20 ETU 750219 1 |
|
DTH-16D-2 (BK) TEL 780575 12 |
|
|
|
|
Unit |
Electra Elite IPK KSU Options |
Stock Number |
|
RAK-U10 Unit |
19” RACK MOUNT UNIT 19” Rack mount unit for Elite IPK KSU |
750394 |
|
External Battery Cable Kit |
EXTERNAL BATTERY BACK-UP CABLE Used to connect locally supplied
external backup batteries |
750386 |
|
HUB (8)-U10 ETU |
The Hub ETU provides an in-skin switching hub for Ethernet
applications. It also provides QoS services as well as port
mirroring. |
750109 |
|
Unit |
Electra Elite IPK Spare Batteries |
Stock Number |
|
System Power Battery |
B64 System Power Battery Back-up - two 12V 2.6Ah |
750830 |
|
P64-U20 PSU |
SPARE POWER SUPPLY Replacement Power Supply unit for the Electra Elite IPK KSU. |
750121 |
|
TDM Interface Packages |
|
Unit |
Digital, Analog and OPX Station Interface |
Stock Number |
|
ESIB (8)-U20 ETU |
Each circuit can support one digital multi-line terminal (Electra
Elite IPK, Electra Elite, Dterm ® Series E or Dterm Series i set, ECR/DHP
Adapter(PGD(2)-U10 ADP), Attendant Add-On Console, Single Line
Telephone adapter, or Dterm Cordless Terminal. ESIB (8)-U20 can mount
ESIE (8)-U20 as piggyback. |
750211 |
|
ESIE (8)-U20 ETU |
ELECTRONIC STATION INTERFACE PIGGYBACK UNIT Same functions as ESIB
(8)-U20. ESIE (8)-U20 is piggyback module on ESIB (8)-U20. This ESIE
(8)-U20 can connect digital multi-line terminal from front RJ61
connectors. |
750219 |
|
TDM Interface Packages |
|
Unit |
Digital, Analog and OPX Station Interface |
Stock Number |
|
SLIB (4)-U10 ETU |
SINGLE LINE INTERFACE UNIT This Single Line Telephone ETU supports 4
Single Line Telephones and/or analog voice mail ports. This ETU
provides Ringing Signal Generator (RSG), and Message Waiting (MW) LED
voltage to Single Line Telephones. Firmware Version 1.73 is required
on IPK II. |
750217 |
|
SLIE (4)-U10 ETU |
SINGLE LINE INTERFACE PIGGY-BACK UNIT Same functions as SLIB(4)-U10
ETI. SLIE(4)-U10 us a piggyback module on SLIB(4)-U10. This piggyback
unit supports 4 Single Line Telephones and/or analog voice mail
ports. |
750218 |
|
OPX (2)-U10 ETU |
LONG LINE TELEPHONE UNIT The Off-Premise Extension ETU provides for
the termination and operation of two off-premise extensions. Each ETU
has a built-in ringer (RSG). |
750230 |
|
TDM Interface Packages |
|
Unit |
Analog Trunk |
Stock Number |
|
COI (8)-U10 ETU |
CENTRAL OFFICE INTERFACE UNIT The Central Office Interface Unit supports 8 outside (CO/PBX) lines.
The outside lines can be a combination of Loop Start or Ground Start DTMF trunks. |
750160 |
|
Unit |
Analog Trunk with Caller ID |
Stock Number |
|
COIB (4)-U30 ETU |
CENTRAL OFFICE INTERFACE UNIT with CALLER ID The Central Office Caller ID ETU detects Caller ID signals from the
central office and sends them to the Main Processor. This card
supports 4 outside (CO/PBX) lines, CO Message Waiting, transmit and
receive pads (volume control) and contains a fax branch connection.
Loop start trunks only. Supports CAMA trunks for E911. |
750449 |
|
COIB (8)-U30 ETU |
CENTRAL OFFICE INTERFACE UNIT with CALLER ID The Central Office Caller ID ETU detects Caller ID signals from the
central office and sends them to the Main Processor. This card
supports 8 outside (CO/PBX) lines and CO Message Waiting and ,
transmit and receive pads (volume control) . Loop-start trunks only.
Supports CAMA trunks for E911. |
750451 |
|
Interface Packages |
|
Unit |
DID / Tie Lines |
Stock Number |
|
DID (4)-U10 ETU |
DIRECT INWARD DIALING INTERFACE UNIT The Direct Inward Dialing Interface supports up to four DID or four
2-way DID lines. Immediate, wink start, delay start and second dial tone signaling are accommodated. |
750170 |
|
|
TIE LINE INTERFACE UNIT |
|
|
TLI (2)-U10 ETU |
The Tie Line Interface ETU supports the termination and operation of
up to two E&M Tie lines (4-wire, type I and type V, and 10/20 pps Dial
Pulse or DTMF). Immediate, wink start, delay start, and second dial
tone signaling are accommodated. |
750180 |
|
Interface Packages |
|
Unit |
Digital Trunk (T1) / ISDN |
Stock Number |
|
DTI-U40 ETU |
DIGITAL TRUNK INTERFACE UNIT The Digital Trunk Interface unit provides both T1 and PRI interface. The T1 Trunk Interface provides for the termination of T1/Fractional
T1 (24 DS-0 channels) lines with ANI. Tie line (E&M), DID signaling,
loop start, and ground start are supported. The Primary Rate Interface
provides for the termination of an ISDN PRI line for voice service
only. This unit supports 4ESS (AT&T Custom), AT&T 5ESS (Lucent
Custom), DMS-100 (Custom and National ISDN) and NI-2 protocols.
Firmware Version 5.00 is required on IPK II. |
750196 |
|
BRT (4)-U20 ETU |
BASIC RATE INTERFACE UNIT The Basic Rate Interface Unit provides 4 channels (8 voice channels)
for ISDN Basic Rate Interface. When connecting to a CO, a Network
Termination Unit (NT1) is required. Firmware Version 4.00 is required
on IPK II. |
750201 |
|
MEGACO IP Station Interface for IPK Telephones IP K-CCIS Trunk
Interface |
|
Unit |
IP Station or IP Trunk Card |
Stock Number |
|
PVA (X)-U10 ETU |
Packet Voice Application This ETU provides support for Media Gateway
or IP K-CCIS trunks. This ETU can assign 16 Media Gateway or 24 IP
K-CCIS trunks. One IPK II IP Resource CD(750874) is required per ETU ordered. |
750235 |
|
IPK II IP Resource CD |
This CD provides software to be loaded on the PVA( )-U10 ETU. It contains software for Media Gateway and IP K-CCIS trunks.
1 required per PVA(x)-U10 ETU(750235). |
750874 |
|
H323 IP Trunk Interface |
|
Unit |
VOIP Trunk Solutions |
Stock Number |
|
IAD H323 |
This ETU provides support for H323 trunks. This ETU provides an H.323
connection to an H.323 network. One IAD H323 ETU supports a maximum 8
connections. Includes CD software. |
750265 |
|
Electra Elite IPK II Applications |
|
Unit |
Applications (Hardware) |
Stock Number |
|
CCH (4)-U10 ETU |
COMMON CHANNEL HANDLER (CCH) (K-CCIS) This ETU provides a common
channel signal through the DTI to a K-CCIS network responsible for
signaling between the CPU and the K-CCIS network. DTI-U40 ETU(750196) is needed for K-CCIS activity. Firmware Version
5.01 and a chip are required in IPK II. |
750145 |
|
CNF(16) U20 ETU |
MULTI-LINE CONFERENCE BRIDGE Provides the ability to support up to 16
party conferences. Each conference is DSP amplified, balanced and
password protected. Simple or Advanced mode supported. |
750176 |
|
Unit |
WIRELESS DECT |
Stock Number |
|
BSU(4M)-U20 ETU |
4-Channel Base Station Unit (Main) for Wireless DECT with connection
for 4 base stations and expand up to 16 Base Stations when using two
BSU(6S) ETUs. This ETU is installed in slots S1~S8
(S2~S8 when using one sub ETU or S3~S8 when using two sub ETUs |
750203 |
|
BSU(2S)-U20 ETU |
2-Channel Base Station Unit (Sub) for Wireless DECT with connection
for two Base Stations and must be used with the BSU(4M)-U20 ETU. This
ETU is installed in the first or second slot to the left of the
BSU(4M)-U20 ETU. |
750202 |
|
BSU(6S)-U20 ETU |
6-Channel Base Station Unit (Sub) for Wireless DECT with connection
for six Base Stations and must be used with the BSU(4M)-U20. This ETU
is installed in the first or second slot to the left of the
BSU(4M)-U20 ETU. |
750204 |
|
DECT, 2.4G, Base Station |
Supports four simultaneous Wireless (DECT) traffic channels at 32
Kbit/s. |
780136 |
|
DECT, 2.4G Repeater Unit |
Provides extended coverage for low traffic areas not covered by a Base
Station. |
780138 |
|
External Antenna |
External Antenna with Cable for repeater. |
780145 |
|
DECT, 2.4G Handset w/Battery |
DECT Handset with Battery |
780004 |
|
DECT, 2.4G Charging Cradle |
Charging Cradle for DECT Handsets |
780137 |
|
DECT, 2.4G, AC Adapter |
AC Adapter for Charging Cradle and Repeater. |
780139 |
|
DECT, 2.4G, Battery (NMh) |
Spare Battery for DECT Handset. |
780140 |
|
DECT, 2.4G, Handset Belt Clip |
Optional Handset Belt clip. |
780141 |
|
Leather Cover |
Leather Cover with Clip for DECT 2.4G Handset. |
780148 |
|
2.4G, Repeater Programming Kit |
Recommend 1/service technician |
780142 |
|
Unit |
DSP Card |
Stock Number |
|
DSPII-U10 UNIT |
Required for VRS or InMail. Mounted onto CPUII. |
750118 |
|
Unit |
Voice Response System |
Stock Number |
|
IPK II VRS FD |
Provides General Message, Personal Greeting, Park and Page, Automated
Attendant, ACD Messages, Transfer to the VRS, Voice Prompting
Messages, 900 Preamble, and Time, Date and Station Number Check.
Inserted to slot of DSPII-U10 UNIT (750118) |
750886 |
